Open Access
28 November 2022 Real-time tracking of brain oxygen gradients and blood flow during functional activation
Sang Hoon Chong, Yihong Ong, Mirna El Khatib, Srinivasa Rao Allu, Ashwin B. Parthasarathy, Joel H. Greenberg, Arjun G. Yodh, Sergei A. Vinogradov
Author Affiliations +
Abstract

Significance

Cerebral metabolic rate of oxygen (CMRO2) consumption is a key physiological variable that characterizes brain metabolism in a steady state and during functional activation.

Aim

We aim to develop a minimally invasive optical technique for real-time measurement of CMRO2 concurrently with cerebral blood flow (CBF).

Approach

We used a pair of macromolecular phosphorescent probes with nonoverlapping optical spectra, which were localized in the intra- and extravascular compartments of the brain tissue, thus providing a readout of oxygen gradients between these two compartments. In parallel, we measured CBF using laser speckle contrast imaging.

Results

The method enables computation and tracking of CMRO2 during functional activation with high temporal resolution (∼7 Hz). In contrast to other approaches, our assessment of CMRO2 does not require measurements of CBF or hemoglobin oxygen saturation.

Conclusions

The independent records of intravascular and extravascular partial pressures of oxygen, CBF, and CMRO2 provide information about the physiological events that accompany neuronal activation, creating opportunities for dynamic quantification of brain metabolism.

1.

Introduction

Oxidative phosphorylation is the primary metabolic pathway by which the brain generates energy, and it requires uninterrupted delivery of oxygen to tissue.1 Oxygen is carried by blood and is distributed via a network of vessels, from which oxygen molecules diffuse along a concentration gradient set by the rate of oxygen consumption, known as the cerebral metabolic rate of oxygen (CMRO2). Because there is minimal buffering of oxygen between the blood and respiring cells, cerebral blood flow (CBF) must rapidly respond to changes in neuronal activity. The oxygen concentration gradients are reflected by the vascular versus tissue (mitochondrial) partial pressures of oxygen (pO2); thus, they encode information about oxygen consumption and supply as well as information about changes in CMRO2 and vascular responses.

Quantification of CMRO2 has been a longstanding goal in neuroscience. In a steady state, CMRO2 can be a useful marker of tissue pathology, such as in stroke,2 traumatic brain injury,3 and cancer.4 By contrast, dynamic measurements of CMRO2 during neuronal activation provide information about the brain metabolic events that underlie functional responses.5 Positron emission tomography (PET) with O15-labeled compounds is arguably the most established method for CMRO2 measurements in a steady-state.6 PET can be used in humans, but quantitative PET requires independent measurements of CBF and the total cerebral blood volume (CBV), and it relies on complex multiparametric models for the calculation of CMRO2.7 Furthermore, the temporal resolution of PET is insufficient for tracking metabolic dynamics during neuronal activation.8

For dynamic tracking of brain responses, the most widely used techniques are blood oxygen level-dependent functional magnetic resonance imaging (BOLD fMRI)9 and functional near infrared spectroscopy (fNIRS).10,11 In both methods, CMRO2 is derived from hemoglobin oxygen saturation, and its quantification requires independent measurements of oxygen extraction fraction, CBF, and CBV.1216 As a result, BOLD fMRI and fNIRS are best suited for probing relative changes in CMRO2, and the resultant CMRO2 dynamics are inherently tied to the dynamics of CBF. However, CMRO2 and CBF may not change in the same way in response to activation, and their timing carries valuable information about the dynamics of neurovascular coupling17 that is inaccessible to BOLD fMRI and fNIRS.

CMRO2 can also be inferred from measurements of lateral gradients of oxygen around individual vessels coupled with diffusion-based models, such as the Krogh-Erlang cylinder model.18 pO2 gradients around vessels were first measured with oxygen microelectrodes.19 More recently, two-photon phosphorescence lifetime microscopy (2PLM)20 has proven superior for spatially resolved pO2 measurements. The 2PLM method is minimally invasive and capable of probing pO2 at multiple locations near vessels in the brain.21,22 However, oxygen mapping by 2PLM requires long observation times, and hence it is currently used only for gradient measurements in steady-states.23,24 Nevertheless, as per this work, phosphorescence lifetime oximetry has been successfully used to measure stimulus-induced changes in brain pO225 at speeds comparable to transients of neuronal activity. Additionally, the laser Doppler method and oxygen microelectrodes have been used concurrently during functional stimulation to track local CBF and intravascular and extravascular pO2 (piO2 and peO2) in selected locations, but CMRO2 was not computed.26

Herein, we introduce and demonstrate an all-optical approach for dynamic measurements of CMRO2. The new methodology is based on quantification of oxygen concentration in the brain using two macromolecular phosphorescent probes, Oxyphors PtG4 and PtR4, placed separately in the intravascular and extravascular compartments. The Oxyphors do not diffuse across the blood brain barrier and have distinguishable optical spectra. Their optical signals can be obtained independently and concurrently for direct measurement of oxygen gradients between the compartments. In our work, we sampled oxygen gradients in rat brain cortex at a rate of 7  Hz, but this sampling frequency can potentially be increased more than 10-fold. In parallel, we measured local CBF by laser speckle contrast imaging (LSCI). Overall, the obtained data enabled us to correlate changes in CMRO2 with changes in CBF and thereby ascertain the timing and relative magnitudes of the physiological events that accompany neuronal activation. The new approach is minimally invasive, offers superior time-resolution (potentially approaching milliseconds), and creates novel opportunities for dynamic tracking and quantification of absolute CMRO2 and neurovascular coupling dynamics.

2.

Materials and Methods

2.1.

Two-color Phosphorescence Lifetime Oximetry

The phosphorescent probes used in this study were Oxyphors PtG4 and PtR4. PtG4 has been used previously.2729 PtR4 was synthesized specifically for this work ( Supplementary Material, p. S3). PtR4 is similar to the probe PdR4,30 except that the central metal ion in the porphyrin is Pt(II) and the shell surrounding the porphyrin in PtR4 is composed of mixed arylglycine/glutamate dendrons. The difference between Pt and Pd porphyrin-based probes has been discussed previously.31 The synthesis and the photophysical data for PtR4 can be found in the Supplementary Material (pp. S3–S9). The probes were calibrated using a setup described previously.30

The instrument for two-color phosphorometry was constructed in-house [Fig. 1(a)]. The light sources for excitation of PtG4 and PtR4 were modulated diode lasers (Power Technology) operating at λmax=630  nm (15 mW) and λmax=517  nm (10 mW), respectively. Both diode lasers have a rise time of 50  ns. Avalanche photodiodes (APDs) were employed for light detection (C12703-01, Hamamatsu; rise time 3.3  μs). The instrument had two channels (Ch1 and Ch2) with the term channel referring to the combination of a laser, optical fiber for transmitting phosphorescence light to a detector, optical filters, and APD. The control of data acquisition was performed using a digital board (NI USB-6351, National Instruments; 1 MHz) that communicated with the host computer via a USB interface. The data acquisition and analysis software was written in C/C++ (Qt, Nokia). (See Supplementary Material, p. S8 for additional details.)

Fig. 1

(a) Scheme of the experimental setup. (b) Representative wide-field image of the craniotomy window over the somatosensory area. Scale bar: 1 mm. The full LSCI imaging area is shown by the dashed square. The solid white square (200  μm×200  μm) indicates the region used for LSCI data processing, which coincided with the focus spot of the phosphorometer lasers (200  μm in diameter). This spot was located 300  μm away from the probe injection site (seen as a greenish area). (c) Optical absorption and phosphorescence spectra of Oxyphors PtG4 (channel 1) and PtR4 (channel 2). The laser lines (635 and 517 nm) of the respective channels and the LSCI laser line (852 nm) are shown by vertical bars. The absorption spectra are scaled by the respective extinction coefficients [ε620(PtG4)1.0×105  M1cm1 and ε510(PtR4)2.0×104  M1cm1]. The emission spectra are scaled such that their areas are proportional to the probes’ phosphorescence quantum yields (ϕPtG4=0.067 and ϕPtR4=0.052). The emission wavelength ranges isolated by the optical filters and seen by the detectors in Ch1 (PtG4) and Ch2 (PtR4) are shown by the shaded areas.

NPh_9_4_045006_f001.png

The light beams from both lasers (Ch1 and Ch2) were focused by lenses (f=60  mm and Ø=12  mm) onto the same spot (diameter0.2  mm) on the brain surface; the spot resided within the region of the cortex responsible for forepaw responses [Fig. 1(b)]. Phosphorescence signals were collected by single-core plastic fibers (Ø=4  mm, Fiberoptic Technology) with tips that were held 2  mm from the excitation spot [Fig. 1(a)]. The phosphorescence in each channel was passed through a series of optical filters and focused by a spherical lens (Ø=10  mm) onto the APD entrance aperture.

To measure pO2 in the intravascular and extravascular compartments, one phosphorescent probe was injected into the vasculature, and the other was injected directly into the interstitial space of the brain tissue. A single data acquisition cycle (duration T=δt+Δt) consisted of an excitation pulse (δt=10  μs), during which the laser was on, followed by the phosphorescence collection period (Δt=290  μs), during which the APD current was digitized and recorded. To increase the signal-to-noise ratio (SNR), multiple cycles (N) were executed in sequence, after which the resulting data array was transferred to the computer. The collected phosphorescence decays were averaged and analyzed by single-exponential fitting, and the phosphorescence decay time was converted to pO2 using a Stern–Volmer-like equation. Once a measurement in one channel was completed, it was followed immediately by measurement in the other channel. The pO2 gradient (ΔpO2), defined here as the difference between volume-averaged piO2 and peO2 (ΔpO2=piO2peO2), was computed as the difference between the readings in the two channels.

For typical acquisition settings (e.g., T=300  μs and N=30), the data collection time for each channel was 10  ms, and the data transfer/analysis required another 10  ms. However, due to hardware limitations, the maximum repetition rate for two-channel acquisition was 7 Hz (70  ms per channel). The significant “dead time” was caused by the internal operation of the digital board, which had to undergo a reset for each measurement cycle. In the future, with more efficient hardware and optimized collection geometry, the measurement rate can be readily increased to >50  Hz.

2.2.

Laser Speckle Contrast Imaging

The principles of LSCI have been discussed previously.32,33 A diode laser (852 nm, 600 mW, and LD852-SE600, Thorlabs) was positioned at a distance of 20  cm from the brain surface, and its beam was directed at 45  deg angle relative to the surface normal. The brain was imaged using a CMOS camera (acA2040-180 km, Basler AG, Germany) equipped with an infinity-corrected optical system composed of two lenses with focal lengths of f=135  mm (Mitakon Zhongyi Mark II Lens for Nikon F, Zhong Yi Optics, China) and f=75  mm (AC508-075-B, Thornlabs). Images (5-ms exposure) were acquired at a frame rate of 20 Hz using custom-written software (LabVIEW, National Instruments). The LSCI field of view (FOV) was 6.2  mm×6.2  mm; the FOV encompassed the focal spot used for the phosphorescence oximetry. LSCI images were analyzed to quantify relative changes of CBF in the brain cortex, as described elsewhere.34

2.3.

Animal Preparation

Twelve adult male Sprague–Dawley rats (250 to 400 g) were used in this study. Rats were anesthetized via the inhalation of a nitrogen:oxygen (70:30) mixture containing isoflurane (4% for initial induction, maintained at 1.5%). A catheter was placed into the left femoral artery for continuous monitoring of the arterial blood pressure (ABP) (507061F pressure transducer, Harvard Apparatus). This catheter was also used for injection of the phosphorescent probe for piO2 measurements and for injections of saline to maintain hydration. The animal’s head was fixed in a stereotaxic frame, and a 6  mm×4  mm cranial window was made in the skull over the forepaw somatosensory area [Fig. 1(b)] using a saline-cooled dental drill. The dura mater was removed, after which the exposed brain surface was continuously irrigated with artificial cerebrospinal fluid ( Supplementary Material, p. S3) heated to 37°C. After the craniotomy was completed, α-chloralose was administered intraperitoneally (60  mg/kg). Simultaneously, the isoflurane dose was gradually decreased and then discontinued over a period of 30 min. Anesthesia was maintained by supplemental doses of α-chloralose (30  mg/kg,1  dose/hr). The depth of anesthesia was verified every 15 min by the toe-pinch method. Two electrodes for electrical stimulation were inserted subdermally into the left forepaw contralateral to the craniotomy site [Fig. 1(a)]. The distal ends of the electrodes were connected to a customizable stimulus isolator (A365, World Precision Instruments). The body temperature was monitored with a rectal probe and was maintained at 37.4°C±0.2°C using a heating pad controlled by a homeothermic monitoring system (Harvard Apparatus). The animals were under the care of the University of Pennsylvania Laboratory Animal Resources. All studies were approved by the University of Pennsylvania Institutional Animal Care and Use Committee.

2.4.

Experimental Sequence

First, stimulation was applied to the animal’s forepaw using electrical current from a stimulus isolator (1.5 mA, 1-ms-long pulses at 3 Hz, and stimulation time 4 s), and LSCI data were collected and analyzed34 to locate the somatosensory cortex region within the exposed craniotomy window. Oxyphors PtR4 and PtG4 were administered as solutions in physiological saline: one intravascularly via femoral catheter (50  μL, 200  μM) and the other (0.1  μL, 300  μM) was injected directly into the brain tissue using a microinjection dispenser (Picospritzer III, Parker Hannifin Precision Fluidics Division) and a micropipette (tip diameter15  μm). The micropipette was inserted to a depth of 200 to 300  μm, and the Oxyphor solution was injected at a rate of 0.1  μL/min. Subsequently, electrical stimulation/LSCI was repeated to confirm that functional responses persisted. The laser assemblies for phosphorescence measurements were positioned above the cranial window [Fig. 1(a)], and phosphorescence signals were measured. If necessary, the amount of intravascular probe was increased by injecting additional solution through the catheter.

Each stimulation cycle was 1-min-long, and it consisted of 4-s-long baseline monitoring, followed by the application of a 4-s-long stimulus (1.5 mA and 1-ms-long pulses at 3 Hz) and a 52-s-long recovery period. Up to 15 sequential stimulation cycles were applied, during which the phosphorescence and LSCI data were recorded.

2.5.

Modeling and Calculation of CMRO2

CMRO2 was computed from the experimentally measured differences between peO2 and piO2 using a two-compartment tissue model published previously.35 In the Supplementary Material (Section 8, p. S10), the model and the solution are described in detail with all assumptions outlined. In brief, the two-compartment model has two governing equations:

Eq. (1)

VidCc(t)dt=CBF(t)[Ca(t)Cv(t)]PSc[Ci(t)Ce(t)],

Eq. (2)

VedCe(t)dt=PSc[Ci(t)Ce(t)]CMRO2(t).
Here Ci and Ce refer to volume-averaged intravascular (blood plasma) and extravascular unbound molecular oxygen (O2) concentrations, respectively; Ca, Cv, and Cc refer to arterial, venous and capillary O2 concentrations, respectively, that include both O2 bound to hemoglobin and unbound O2 dissolved in blood plasma; Vi and Ve refer to the volumes of the intravascular and extravascular compartments within the entire tissue volume, respectively, with Vt (Vt=Vi+Ve) and Vi and Ve usually defined per 100 g of tissue; PSc is a mass transfer proportionality parameter that is often written as the product of capillary O2 permeability, P (cm/s), and capillary surface area, Sc [cm2/100  g tissue]. In the physiological oxygen range, the concentrations Ce and Ci [Eq. (2)] are proportional to peO2 and piO2.

Equation (1) relates the rate of change in the capillary oxygen (Cc) to the oxygen influx due to CBF and oxygen loss via diffusion into the extravascular space. Equation (2) is a mass-balance statement that accounts for oxygen diffusion from capillaries and oxygen consumption in the extravascular space. In this work, only Eq. (2) was used; Eq. (1) is shown as a reminder of the comparatively indirect way by which CMRO2 is deduced in the BOLD fMRI and fNIRS methods.

To determine CMRO2 as a function of time, Eq. (2) was evaluated numerically with experimental inputs of Ci and Ce, which in turn were derived from phosphorescence lifetime measurements. The time-derivative dCe/dt was calculated using the finite difference method. The code was written in MATLAB. The values of the constants in the model, e.g., Ve and PSc, were obtained using published microscopic physiological parameters and the Krogh-Erlang cylinder model18 ( Supplementary Material, p. S16). The choice of PSc and its effect on the magnitude and temporal profile of CMRO2 are discussed below.

3.

Results and Discussion

3.1.

Measurement Method

In this work, we developed a new variant of the phosphorescence quenching method36 for concurrent measurements of oxygen concentrations in the intravascular and extravascular compartments of rat brain. We employed two dendritic polyethyleneglycol-coated phosphorescent probes, Oxyphors,30,31 that do not cross the blood brain barrier21,22,27 and have minimally overlapping absorption and emission spectra. Thus, phosphorescence signals from the two probes can be retrieved with no cross-talk, and because one probe circulated in blood and the other resided in the extravascular space, piO2 and peO2 could be measured concurrently.

Excitation of a mixture of PtR4 and PtG4 at 635 nm results only in phosphorescence of PtG4 [Fig. 1(c)]. However, excitation at 517 nm, aimed at the absorption Q band of PtR4, induces a weak but nonnegligible emission from PtG4. Therefore, several optical filters were used to remove unwanted signals from each channel ( Supplementary Material, p. S8). As a result, the phosphorescence spectrum of PtR4 was attenuated by nearly 60% [Fig. 1(c)]. This narrowing of the spectral range, coupled with a lower molar extinction coefficient and a lower emission quantum yield, caused the PtR4 signal to be 10–15 times weaker than that of PtG4, even when equal amounts of the probes were dissolved in an optically clear medium, such as an aqueous solution in optical cells. In vivo the difference between PtR4 and PtG4 was further exacerbated by stronger attenuation of excitation at 517 nm and of the phosphorescence of PtR4 due to endogenous tissue absorption. Thus, the phosphorescence signal of PtR4 was 10–20 times weaker than that of PtG4 even when PtR4 was injected in the brain in 10-fold higher concentration. Consequently, SNR in Ch2 [Fig. 1(c)] was significantly lower than that in Ch1, irrespective of whether PtR4 was injected into blood or interstitial space. Despite this challenge, pO2 readings were obtained at a rate of 7 Hz for two channels and were sufficient for resolving transients in respiratory and vascular activity upon neuronal activation. In most experiments, PtR4 was delivered intravascularly, and its concentration could be increased via additional injections during the experiments through the catheter, if necessary.

3.2.

Recordings of peO2, piO2, and CBF

An example of raw unprocessed traces of peO2 (Ch1/PtG4), piO2 (Ch2/PtR4), and CBF during a series of stimulations is shown in Fig. 2(a). Importantly, the ABP was not affected by stimulations (see Supplementary Material, p. S23). The recording of pO2 was paused between the stimulations to minimize brain exposure to the excitation light and associated phototoxicity. All three parameters exhibited a sharp rise after stimulation, followed by a decrease to the baseline level. Immediately upon the start of the stimulation, peO2 exhibits a characteristic “initial dip” due to the rapid increase in the local oxygen consumption by activated cells [Fig. 2(b)]. On average, the dip minima occurred 0.8±0.1  s after the onset of stimulation, in agreement with previous measurements.22,23 The observation of such dips in microscopic experiments typically requires the averaging of hundreds of simulation trials;22,23 in our experiments, remarkably, the dips could be seen in practically all individual stimulation events. These signals were strong in part because they originated from a large excitation volume that likely encompassed the entire activation region. However, this volume also includes cells with oxygen consumption that does not change significantly upon activation, and hence, the amplitudes of the dips are expected to be lower due to “signal dilution.”

Fig. 2

Raw unprocessed data obtained in an experiment consisting of 13 consecutive forepaw stimulations, accompanied by panel (a) CBF normalized to the initial baseline, and piO2 and peO2 measurements in the somatosensory area of the rat brain. (b) Overlapping traces of peO2, synchronized at the start of the stimulation (t=0). The stimulation period is shown by a pink rectangle.

NPh_9_4_045006_f002.png

The average baseline piO2 was 33.5±0.5  mmHg (mean for 13 events, measured during the 4s prior to stimulation, and ± standard deviation of the mean). This baseline piO2 is on the lower side of piO2 values reported previously,2123,37 possibly due to the use of α-chloralose anesthetic. Anesthesia is known to have pronounced effects on tissue pO2.37,38 The average baseline peO2 was 21.3±0.2  mmHg, and the resulting piO2/peO2 difference was 12.2±0.4  mmHg. In previous studies performed on rat brain and utilizing 2PLM and isoflurane as the anesthetic, pO2 drops of 15  mmHg were seen over 25-μm distances from isolated arterioles, corresponding to the gradients of 0.6  mmHg/μm.24 Measurements around capillaries in rat brain using microelectrodes (with pentobarbital anesthesia) produced somewhat lower gradients, 0.45  mmHg/μm.19 In the present case, piO2 values correspond mainly to the capillary pO2 because the total volume of blood in capillaries is larger, and optical excitation in thin capillaries is much more efficient than in large vessels. The peO2 represents the entire extravascular space within the excitation volume. Assuming an average intercapillary distance of 60  μm,39 the measured mean piO2 and peO2 values result in the gradient of 0.8  mmHg/μm and consequently correspond to a relatively high baseline CMRO2. This larger apparent gradient is consistent with sampling at a greater depth in the cortex and therefore higher neuron density and higher rates of oxygen consumption. Note, however, that we cannot unambiguously exclude contributions from systematic errors (see Sec. 3.5) in the measurements of piO2 and/or peO2, which will be further analyzed and corrected as the method develops.

In a number of cases, only four to five consecutive stimulations were successful, after which the brain lost responsiveness. The latter observation suggests that measurements could have been causing some tissue damage. However, our attempts to correlate the early loss of response with the duration of photo-exposure and/or probe dose were not conclusive. On balance, the loss of responsiveness appeared to be more frequent in animals for which green light excitation (517 nm and Ch2) was used in combination with PtR4 delivered into the extravascular space.

3.3.

Calculation of CMRO2

According to Eq. (2), CMRO2 can be derived from the experimentally measured values of Ce and Ci and the time derivative, dCe/dt, for extravascular oxygen. In previous work, the evaluation of this time derivative, as well as of the derivative dCc/dt in Eq. (1), was not possible. Therefore, the derivatives were omitted, and CMRO2 was computed from instantaneous values of CBF, Ca and Cv (e.g., CMRO2=CBF×[CaCv]). This approach effectively assumes that the system is (always) in a steady state, even during functional activation. As a result, the deduced dynamics of CMRO2 are inherently tied to that of CBF.1214,40

The ability to independently measure Ce and its time derivative (dCe/dt) is a new feature that makes our technique unique and potentially more accurate than methods used previously. To distinguish between the traditional and present approaches, we introduce the terms full- and truncated-dynamic CMRO2 (fCMRO2 and tCMRO2). fCMRO2 is computed using the complete Eq. (2), including the derivative dCe/dt; tCMRO2 is computed ignoring the time derivative. With the same input data for Ce and Ci, the difference between the computed fCMRO2 and tCMRO2 depends on coefficients Ve and PSc [Eq. (2)]. The value of Ve (tissue extravascular volume) for brain tissue is well constrained41,42 ( Supplementary Material, p. S16). By contrast, the published values for the product PSc vary widely, reflecting the fact that the assessment of the oxygen diffusion coefficient in tissue is notoriously difficult. Unfortunately, both the magnitude and temporal profile of CMRO2 are strongly affected by the choice of PSc. Example traces of fCMRO2 and tCMRO2 based on the same input data, but using different values of PSc, are shown in Fig. 3(a). These profiles and all other traces shown in Figs. 3 and 4 were computed by averaging the CMRO2 traces for 13 stimulations (Fig. 2), whereby the individual CMRO2 traces were obtained by solving Eq. (2) using the respective traces of piO2 and peO2. The solutions were obtained with or without inclusion of the time derivative.

Fig. 3

Averaged traces obtained in the experiment shown in Fig. 2. The stimulation period is shown by the pink rectangle. All traces are synchronized at the start of the stimulation (t=0). (a) Computed traces of fCMRO2 and tCMRO2 (see the text for definitions) for three different values of parameter PSc. Traces of CBF, peO2, piO2, tCMRO2 (b), and fCMRO2 (c) (calculated for PSc=210  mL/s) normalized by their baseline values to emphasize relative changes in the magnitudes.

NPh_9_4_045006_f003.png

Fig. 4

Normalized traces of piO2, peO2, CBF, and CMRO2. Time courses of (a) tCMRO2 and (b) fCMRO2 (computed for PSc=210  mL/s) relative to the time courses of piO2, peO2, and CBF. The stimulation period is shown by a pink rectangle. All traces were smoothed and synchronized at the start of the stimulation (t=0) and normalized by their maximal amplitudes for timing analysis ( Supplementary Material, p. S20). Insets: initial period after activation. Δ: delay (at half-maximum) between the traces of piO2 and peO2.

NPh_9_4_045006_f004.png

When PSc is large, the first term on the left side of Eq. (2) is dominant, and the profiles of fCMRO2 and tCMRO2 strongly overlap [Fig. 3(a)]. However, for smaller PSc, fCMRO2 increasingly lags behind tCMRO2, as the contribution of the term Ve×dCe/dt becomes nonnegligible. This time-lag effect is a direct consequence of the inclusion of the time-derivative dCe/dt. The solution of Eq. (2) contains an exponential term with time constant τ=Ve/PSc that is an intrinsic feature of the perturbation response kinetics. For example, if the system starts in a steady state (dCe/dt=0) and then piO2 increases (or decreases) instantly in stepwise fashion, then a new steady-state CMRO2 is reached in exponential fashion with time constant τ. Notably, the delay between the rise of piO2 versus peO2 depends on the parameter PSc and on the temporal variation of physiological responses. In addition, the parameter PSc affects the absolute magnitude of CMRO2. In our analysis, we used the value PSc=210  mL/s/100  g tissue. This choice and the choices of other values were made based on the published microscopic physiological parameters and the Krogh-Erlang cylinder model ( Supplementary Material, p. S16).

3.4.

Magnitude and Dynamics of Responses

In contrast to prior work, our experiments enable the calculation of CMRO2 solely from oximetry data without reliance on CBF. Additionally, we independently measured CBF using LSCI. Thus, taken together, our measurements provide a unique opportunity to compare the response of all four parameters, CBF, piO2, peO2, and CMRO2, and thereby uncover physiologically important information about the response magnitude and dynamics that is not obtainable by other methods.

fCMRO2 and tCMRO2 were computed using the piO2 and peO2 data from 13 stimulations (Fig. 2). The CBF, piO2, peO2, and CMRO2 traces were averaged and normalized either by the respective baseline values [Figs. 3(b) and 3(c)] or by the maximal amplitudes, i.e., the difference between the baseline and the peak value of the trace (Fig. 4). Baseline normalization helps to visualize relative changes in magnitude, whereas normalization by the amplitude has been used previously for timing analysis.43 Both fCMRO2 and tCMRO2 were computed to illustrate the difference between the two methods of calculation, particularly in relation to the timing analysis.

Prior to activation, CBF, piO2 and peO2 and CMRO2 are at their baseline levels; the baseline CMRO2 value is 3.5  μmol/s/100  g tissue [Fig. 3(a)], which is within the range of reported baseline CMRO2 values for the rat brain.44,45 Activation causes an immediate increase in the energy consumption by neurons and other cells, and the mitochondrial oxidative phosphorylation responds nearly instantaneously by elevating the rate of adenosine triphosphate (ATP) synthesis and, consequently, CMRO2. This rise in the energy consumption is the key trigger that sets in motion the cascade of events that define the time courses of all measured parameters.

With respect to the timing analysis, the tCMRO2 and fCMRO2 models will exhibit the same behavior in the limit of large PSc. This behavior is also the same as for the traditional steady-state model because the time-derivative term in Eq. (2) vanishes in the large PSc limit. However, it should be noted that the absolute magnitude of CMRO2 also depends on PSc. Ultimately, it is desirable that the chosen value of PSc should give the correct CMRO2 dynamics and magnitude.

First, it is useful to examine the timing of the events according to the tCMRO2 model, which implies that the rate of change in CBF, piO2, and peO2 is much lower than the rate of oxygen diffusion over the distance separating the source (capillaries) and the consumption sites (mitochondria in cells). The normalized traces of all measured parameters and tCMRO2 are shown in Fig. 4(a).

The rapid rise in CMRO2 due to functional stimulation results in local depletion of oxygen, which is manifested by the “initial dip” in the trace of peO2 with a minimum that is reached at 1  s from the start of the activation. Similar delays between the stimulation onset and the dip have been reported previously.22,23 The increase in the energy consumption results in the vascular response of up-stream arterioles, inducing their dilation, via a pathway known as neurovascular coupling.2,17 As a result, local CBF begins to rise, bringing new oxygenated blood to the activation region. The propagation of the neurovascular coupling cascade is much faster than the time resolution of our measurements, while our experimental traces clearly show, in spite of the noise, that the rise in CBF is delayed relative to the rise in CMRO2 [Fig. 4(a)]. Presumably, this delay is associated with the time needed for arterioles to dilate and for the blood to reach the activation region.

The rise in piO2 begins nearly simultaneously with the rise in CBF, reflecting the fact that arterial blood flowing into the region contains more oxygen. The incoming oxygen diffuses from the capillaries into the extravascular space, and its flux compensates for and then exceeds the rate of oxygen consumption, causing peO2 to curve around the minimum (dip region) and start rising. The subsequent trace of peO2 follows that of piO2 but with a delay Δ0.6  s (measured at half-maximum), consistent with previous observations.43 Delay Δ depends on the interplay of dynamics between CBF and CMRO2 and the diffusion of oxygen from the blood to the consumption sites. As noted above, in the limit of large PSc, the diffusion is fast, and delay Δ is set almost solely by the relative changes in CBF versus CMRO2.

Soon after the end of the stimulation, all four parameters reach their peak values and begin to decline. At its maximum, CMRO2 is 6.0  μmol/sec/100  g tissue [Fig. 3(a), middle panel], i.e., 1.8 times higher than its baseline value [Fig. 3(b)], and the respective increase in CBF is 1.5×. In other experiments (n=3, averaged over 4 to 5 stimulations), the respective increases in CBF and CMRO2 were reversed, e.g., 1.4× and 1.2×, respectively. The observation of a larger increase in CMRO2 compared with that in CBF is somewhat unusual, because many (but not all) previous studies have found that CBF response exceeds CMRO2 response in magnitude.13,14,40 It is possible that the inversion seen in our experiments was influenced by some systematic measurement errors (see Sec. 3.5). However, in principle, the inversion is not impossible because the amount of oxygen delivered to the activation area, even upon moderate increase in CBF, can still overwhelm the demand caused by a large increase in CMRO2 (due to the very high oxygen-carrying capacity of hemoglobin). Indeed, the pO2 traces showed characteristic “overshoots” similar in magnitude to overshoots reported previously.23 The overshoots have been hypothesized to be a consequence of the anatomical structure of the brain, whereby arterioles triggered by neurovascular coupling supply oxygen to a much larger volume than the actual activated region.1,23

After reaching their maxima, all of the parameters gradually return to the respective baselines. Interestingly, CMRO2, piO2, and peO2 decline at a similar rate, whereas the decrease in the CBF is somewhat steeper. This observation suggests that a signal for the cessation of arterial dilation is issued close to the time when CMRO2 levels off and begins to fall, but before it drops significantly. It appears that the system sends a feedback signal to attenuate arterial blood supply when oxygen in the pool is still sufficient for maintaining CMRO2 at an elevated level. In this regard, it is important to stress that CMRO2 is independent of pO2 over the physiological range.46,47 Changes in CBF and/or pO2 neither affect nor control CMRO2. Rather, it is CMRO2, which is set by the rate of ATP consumption through changes in the cellular energy state,48 that drives the events in the context of our experiment. The vascular system merely responds to changes in CMRO2, which depends on changes in the energy state to keep the oxygen supply above a certain threshold level.

The full-dynamic model suggests a more complex profile of CMRO2, particularly near the onset of the stimulation [Fig. 4(b)]. In this case, a clear initial rise in fCMRO2 triggers an increase in CBF. This initial rise in fCMRO2 is followed by a flattening of the response for a brief period (0.3 to 1.3 s) and finally by a steady rise. As in the case of tCMRO2 [Fig. 4(a)], the initial changes in fCMRO2 trigger an increase in CBF; however, starting from 1.5  s fCMRO2 does not lead to CBF, but instead their traces roughly overlap. The dynamics on longer time scales discussed above are essentially the same for both models.

The peak fCMRO2 value is somewhat lower than that predicted by the truncated model, showing an 1.7× increase relative to the baseline level [Fig. 3(c)]. The subsequent decline in CMRO2 is also slightly different, i.e., the trace in Fig. 4(b) versus Fig. 4(a) is more delayed in time. However, these differences are not large, and the poststimulation profiles varied significantly between animals, making comparisons difficult at this stage.

The differences between the traces of tCMRO2 and fCMRO2 offer new means for exploring underlying physiological assumptions in the models. While recognizing the limited time resolution of our measurements and uncertainty due to the noise, the temporal behavior of fCMRO2 clearly does not conform to traditional expectations. It is tempting to speculate about the origin of the initial feature (“bump”) in the profile of the dynamic CMRO2. One possibility is that the choice of PSc (210  mL/s) in our estimations was not correct, and with larger PSc values, the full-dynamic model would converge to the traditional steady-state limit. However, the baseline CMRO2 magnitude would then be larger, whereas essentially all prior estimates of PSc give values in the range of 35 to 230  mL/s.49 It is also possible that systematic measurement errors could lead to overestimation of oxygen gradients. If the actual gradients are lower, then the same baseline CMRO2s would correspond to higher PScs. At this stage, we do not advocate for any particular set of assumptions. Rather, we emphasize that evidence from our qualitatively new methodology takes first steps toward a more critical examination of models/model inputs.

3.5.

Limitations

As mentioned throughout the text, several limitations in the current implementation of the method could cause systematic measurement errors.

  • 1. First and foremost, the optical frequencies (wavelengths) used for probing piO2 and peO2 in our experiment were different (by design) to eliminate the cross-talk between the two measurement channels. However, the effective depth of sampling by light is wavelength-dependent due to the endogenous absorption and scattering. Strong optical heterogeneity of tissue makes it difficult to evaluate the difference in the sampling depth, but estimates based on brain optical properties suggest that the sampling depth for PtR4 was 3× less than for PtG4. Consequently, the two probed volumes were unequal, which could affect quantification of the oxygen gradients.

    In the future, it should be possible to select two probes excitable at the same wavelength, but having minimally overlapping phosphorescence spectra, both in the near-infrared region, wherein the endogenous optical absorption spectrum is nearly flat. Using appropriate optical filtering, the signals of the probes will be sampled independently, and the difference between the probed volumes will be minimized. A selection of dendritic oxygen probes with different optical parameters is available30,31,50 and will be tested in the future.

  • 2. Because the brain tissue after the craniotomy was exposed to room-temperature air, a temperature gradient from the surface down was established. Hemoglobin affinity for oxygen, phosphorescence decay times, and oxygen quenching parameters of the probes are all temperature-dependent. Thus, the combination of the temperature gradient, which was unknown, with the different sampling depths for the two probes (see above) could have an effect on the measured apparent oxygen gradients. Again, minimizing the difference between the sampling volumes should decrease the associated systematic error.

  • 3. One of the principal strengths of all-optical methodology is its minimal invasiveness. However, in our experiments, one of the probes had to be delivered by direct injection into the brain tissue close to the measurement site, potentially damaging the brain. To circumvent this problem in the future, it should be possible to introduce the extravascular pO2 probe by injection into the cisterna magna,50 far away from the measurement site, and thus avoid tissue damage.

4.

Conclusions

We presented the first demonstration of real-time tracking of tissue oxygen gradients concurrently with local blood flow during and after functional activation of rat brain. In contrast to measuring the average oxygen concentration, the technique provides a direct observation window on the rate of the brain metabolism, which is assessed independently from CBF. The method utilizes a combination of the phosphorescence quenching oximetry, employing two optically distinguishable membrane-impermeable oxygen probes, with LSCI. In spite of technical challenges, the technique proved capable of extracting information about the timing of metabolic events accompanying neuronal activation, not obtainable by any other existing method. The innovative method also permitted direct comparison of full-dynamic versus truncated-dynamic (steady state) models based on the same experimental input. As technology develops, we anticipate that the method will become more broadly available for testing drugs and other effectors of brain metabolism, and it should permit more rigorous examination of metabolism models.

Disclosures

S.A.V. has partial ownership of Oxygen Enterprises Ltd, which owns the intellectual property for phosphorescent probes technology (US Pat. No. 9,556,213; US, 2017/0137449 A1). All other authors declare no competing interests.

Acknowledgments

Support of Grant Nos. EB027397, EB028941 (SAV), NS060653, EB015893 (AGY), and HL145092 (MEK) from the US National Institutes of Health is gratefully acknowledged. The authors are grateful to Drs. David F. Wilson, Wesley Baker, Anna Devor, Tiffany Ko, and Brian White for valuable discussions.

References

1. 

D. F. Wilson and F. M. Matschinsky, “Cerebrovascular blood flow design and regulation: vulnerability in aging brain,” Front. Physiol., 11 16 https://doi.org/10.3389/fphys.2020.584891 FROPBK 0301-536X (2020). Google Scholar

2. 

H. Girouard and C. Iadecola, “Neurovascular coupling in the normal brain and in hypertension, stroke, and Alzheimer disease,” J. Appl. Physiol., 100 (1), 328 –335 https://doi.org/10.1152/japplphysiol.00966.2005 (2006). Google Scholar

3. 

J. F. Soustiel et al., “Monitoring of cerebral blood flow and metabolism in traumatic brain injury,” J. Neurotrauma, 22 (9), 955 –965 https://doi.org/10.1089/neu.2005.22.955 JNEUE4 0897-7151 (2005). Google Scholar

4. 

A. Stadlbauer et al., “MR imaging-derived oxygen metabolism and neovascularization characterization for grading and IDH gene mutation detection of gliomas,” Radiology, 283 (3), 799 –809 https://doi.org/10.1148/radiol.2016161422 RADLAX 0033-8419 (2017). Google Scholar

5. 

R. B. Buxton, “Interpreting oxygenation-based neuroimaging signals: the importance and the challenge of understanding brain oxygen metabolism,” Front. Neuroenergetics, 2 8 https://doi.org/10.3389/fnene.2010.00008 (2010). Google Scholar

6. 

M. A. Mintun et al., “Brain oxygen utilization measured with O15 radiotracers and positron emission tomography,” J. Nucl. Med., 25 (2), 177 –187 JNMEAQ 0161-5505 (1984). Google Scholar

7. 

M. A. Mintun et al., “Blood flow and oxygen delivery to human brain during functional activity: theoretical modeling and experimental data,” Proc. Natl. Acad. Sci. U. S. A., 98 (12), 6859 –6864 https://doi.org/10.1073/pnas.111164398 (2001). Google Scholar

8. 

A. P. Fan et al., “Quantification of brain oxygen extraction and metabolism with O15-gas PET: a technical review in the era of PET/MRI,” Neuroimage, 220 117136 https://doi.org/10.1016/j.neuroimage.2020.117136 NEIMEF 1053-8119 (2020). Google Scholar

9. 

Z. B. Rodgers et al., “MRI-based methods for quantification of the cerebral metabolic rate of oxygen,” J. Cereb. Blood Flow Metab., 36 (7), 1165 –1185 https://doi.org/10.1177/0271678X16643090 (2016). Google Scholar

10. 

M. Ferrari and V. Quaresima, “A brief review on the history of human functional near-infrared spectroscopy (fNIRS) development and fields of application,” Neuroimage, 63 (2), 921 –935 https://doi.org/10.1016/j.neuroimage.2012.03.049 NEIMEF 1053-8119 (2012). Google Scholar

11. 

M. A. Yucel et al., “Functional near infrared spectroscopy: enabling routine functional brain imaging,” Curr. Opin. Biomed. Eng., 4 78 –86 https://doi.org/10.1016/j.cobme.2017.09.011Get (2017). Google Scholar

12. 

J. P. Culver et al., “Diffuse optical tomography of cerebral blood flow, oxygenation, and metabolism in rat during focal ischemia,” J. Cereb. Blood Flow Metab., 23 (8), 911 –924 https://doi.org/10.1097/01.WCB.0000076703.71231.BB (2003). Google Scholar

13. 

T. Durduran et al., “Diffuse optical measurement of blood flow, blood oxygenation, and metabolism in a human brain during sensorimotor cortex activation,” Opt. Lett., 29 (15), 1766 –1768 https://doi.org/10.1364/OL.29.001766 OPLEDP 0146-9592 (2004). Google Scholar

14. 

A. Dunn et al., “Spatial extent of oxygen metabolism and hemodynamic changes during functional activation of the rat somatosensory cortex,” Neuroimage, 27 (2), 279 –290 https://doi.org/10.1016/j.neuroimage.2005.04.024 NEIMEF 1053-8119 (2005). Google Scholar

15. 

R. B. Buxton and L. R. Frank, “A model for the coupling between cerebral blood flow and oxygen metabolism during neural stimulation,” J. Cereb. Blood Flow Metab., 17 (1), 64 –72 https://doi.org/10.1097/00004647-199701000-00009 (1997). Google Scholar

16. 

F. Hyder, R. Shulman and D. L. Rothman, “A model for the regulation of cerebral oxygen delivery,” J. Appl. Physiol., 85 (2), 554 –564 https://doi.org/10.1152/jappl.1998.85.2.554 (1998). Google Scholar

17. 

C. Iadecola, “The neurovascular unit coming of age: a iourney through neurovascular coupling in health and disease,” Neuron, 96 (1), 17 –42 https://doi.org/10.1016/j.neuron.2017.07.030 NERNET 0896-6273 (2017). Google Scholar

18. 

A. Krogh, “The supply of oxygen to the tissues and the regulation of the capillary circulation,” J. Physiol., 52 (6), 457 –474 https://doi.org/10.1113/jphysiol.1919.sp001844 JPHYA7 0022-3751 (1919). Google Scholar

19. 

E. Vovenko, “Distribution of oxygen tension on the surface of arterioles, capillaries and venules of brain cortex and in tissue in normoxia: an experimental study on rats,” Pflugers Arch., 437 (4), 617 –623 https://doi.org/10.1007/s004240050825 (1999). Google Scholar

20. 

O. S. Finikova et al., “Oxygen microscopy by two-photon-excited phosphorescence,” Chem. Phys. Chem., 9 (12), 1673 –1679 https://doi.org/10.1002/cphc.200800296 (2008). Google Scholar

21. 

S. Sakadzic et al., “Two-photon high-resolution measurement of partial pressure of oxygen in cerebral vasculature and tissue,” Nat. Methods, 7 (9), 755 –759 https://doi.org/10.1038/nmeth.1490 1548-7091 (2010). Google Scholar

22. 

J. Lecoq et al., “Simultaneous two-photon imaging of oxygen and blood flow in deep cerebral vessels,” Nat. Med., 17 (7), 893 –898 https://doi.org/10.1038/nm.2394 1078-8956 (2011). Google Scholar

23. 

A. Devor et al., “Overshoot” of O2 is required to maintain baseline tissue oxygenation at locations distal to blood vessels,” J. Neurosci., 31 (38), 13676 –13681 https://doi.org/10.1523/JNEUROSCI.1968-11.2011 JNRSDS 0270-6474 (2011). Google Scholar

24. 

S. Sakadžić et al., “Two-photon microscopy measurement of cerebral metabolic rate of oxygen using periarteriolar oxygen concentration gradients,” Neurophotonics, 3 (4), 045005 https://doi.org/10.1038/nmeth.1490 (2016). Google Scholar

25. 

B. M. Ances et al., “Dynamic changes in cerebral blood flow, O2 tension and calculated cerebral metabolic rate of O2 during functional activation using oxygen phosphorescence quenching,” J. Cereb. Blood Flow Metab., 21 (5), 511 –516 https://doi.org/10.1097/00004647-200105000-00005 (2001). Google Scholar

26. 

A. L. Vazquez et al., “Changes in cerebral arterial, tissue and venous oxygenation with evoked neural stimulation: implications for hemoglobin-based functional neuroimaging,” J. Cereb. Blood Flow Metab., 30 (2), 428 –439 https://doi.org/10.1038/jcbfm.2009.213 (2010). Google Scholar

27. 

C. T. Suilender et al., “Imaging of cortical oxygen tension and blood flow following targeted photothrombotic stroke,” Neurophotonics, 5 (3), 035003 https://doi.org/10.1117/1.NPh.5.3.035003 (2018). Google Scholar

28. 

C. Christodoulou et al., “Live-animal imaging of native haematopoietic stem and progenitor cells,” Nature, 578 (7794), 278 –283 https://doi.org/10.1038/s41586-020-1971-z (2020). Google Scholar

29. 

X. Cao et al., “Tissue pO2 distributions in xenograft tumors dynamically imaged by Cherenkov-excited phosphorescence during fractionated radiation therapy,” Nat. Commun., 11 573 https://doi.org/10.1038/s41467-020-14415-9 (2020). Google Scholar

30. 

T. V. Esipova et al., “Two new “protected” oxyphors for biological oximetry: properties and application in tumor imaging,” Anal. Chem., 83 (22), 8756 –8765 https://doi.org/10.1021/ac2022234 ANCHAM 0003-2700 (2011). Google Scholar

31. 

A. Y. Lebedev et al., “Dendritic phosphorescent probes for oxygen imaging in biological systems,” ACS Appl. Mater. Interfaces, 1 (6), 1292 –1304 https://doi.org/10.1021/am9001698 AAMICK 1944-8244 (2009). Google Scholar

32. 

A. K. Dunn et al., “Dynamic imaging of cerebral blood flow using laser speckle,” J. Cereb. Blood Flow Metab., 21 (3), 195 –201 https://doi.org/10.1097/00004647-200103000-00002 (2001). Google Scholar

33. 

S. M. Kazmi et al., “Flux or speed? Examining speckle contrast imaging of vascular flows,” Biomed. Opt. Express, 6 (7), 2588 –2608 https://doi.org/10.1364/BOE.6.002588 BOEICL 2156-7085 (2015). Google Scholar

34. 

T. Durduran et al., “Spatiotemporal quantification of cerebral blood flow during functional activation in rat somatosensory cortex using laser-speckle flowmetry,” J. Cereb. Blood Flow Metab., 24 (5), 518 –525 https://doi.org/10.1097/00004647-200405000-00005 (2004). Google Scholar

35. 

R. Valabregue et al., “Relation between cerebral blood flow and metabolism explained by a model of oxygen exchange,” J. Cereb. Blood Flow Metab., 23 (5), 536 –545 https://doi.org/10.1097/01.WCB.0000055178.31872.38 (2003). Google Scholar

36. 

J. M. Vanderkooi et al., “An optical method for measurement of dioxygen concentration based on quenching of phosphorescence,” J. Biol. Chem., 262 5476 –5482 https://doi.org/10.1016/S0021-9258(18)45596-2 JBCHA3 0021-9258 (1987). Google Scholar

37. 

D. G. Lyons et al., “Mapping oxygen concentration in the awake mouse brain,” eLife, 5 e12024 https://doi.org/10.7554/eLife.12024 (2016). Google Scholar

38. 

D. F. Wilson et al., “Oxygen pressures in the interstitial space and their relationship to those in the blood plasma in resting skeletal muscle,” J. Appl. Physiol., 101 (6), 1648 –1656 https://doi.org/10.1152/japplphysiol.00394.2006 (2006). Google Scholar

39. 

C. Leithner and G. Royl, “The oxygen paradox of neurovascular coupling,” J. Cereb. Blood Flow Metab., 34 (1), 19 –29 https://doi.org/10.1038/jcbfm.2013.181 (2014). Google Scholar

40. 

R. D. Hoge et al., “Simultaneous recording of task-induced changes in blood oxygenation, volume, and flow using diffuse optical imaging and arterial spin-labeling MRI,” Neuroimage, 25 (3), 701 –707 https://doi.org/10.1016/j.neuroimage.2004.12.032 NEIMEF 1053-8119 (2005). Google Scholar

41. 

S. Lin et al., “Cerebral capillary bed structure of normotensive and chronically hypertensive rats,” Microvasc. Res., 40 (3), 341 –357 https://doi.org/10.1016/0026-2862(90)90032-M MIVRA6 0026-2862 (1990). Google Scholar

42. 

A. Santuy et al., “A quantitative study of the distribution of mitochondria in the neuropil of the juvenile rat somatosensory cortex,” Cereb. Cortex, 28 (10), 3673 –3684 https://doi.org/10.1093/cercor/bhy159 53OPAV 1047-3211 (2018). Google Scholar

43. 

K. Masamoto et al., “Trial-by-trial relationship between neural activity, oxygen consumption, and blood flow responses,” Neuroimage, 40 (2), 442 –450 https://doi.org/10.1016/j.neuroimage.2007.12.011 NEIMEF 1053-8119 (2008). Google Scholar

44. 

B. Eklof et al., “Blood flow and metabolic rate for oxygen in the cerebral cortex of the rat,” Acta. Physiol. Scand., 88 (4), 587 –589 https://doi.org/10.1111/j.1748-1716.1973.tb05489.x (1973). Google Scholar

45. 

T. Watabe et al., “Quantitative evaluation of cerebral blood flow and oxygen metabolism in normal anesthetized rats: O15-labeled gas inhalation PET with MRI fusion,” J. Nucl. Med., 54 (2), 283 –290 https://doi.org/10.2967/jnumed.112.109751 JNMEAQ 0161-5505 (2013). Google Scholar

46. 

B. Chance, “The kinetics and inhibition of cytochrome components of the succinic oxidase system,” J. Biol. Chem., 197 (2), 557 –576 https://doi.org/10.1016/S0021-9258(18)55610-6 JBCHA3 0021-9258 (1952). Google Scholar

47. 

D. F. Wilson et al., “Oxygen dependence of cellular energy metabolism,” Arch. Biochem. Biophys., 195 (2), 485 –493 https://doi.org/10.1016/0003-9861(79)90375-8 (1979). Google Scholar

48. 

D. F. Wilson, “Oxidative phosphorylation: unique regulatory mechanism and role in metabolic homeostasis,” J. Appl. Physiol., 122 (3), 611 –619 https://doi.org/10.1152/japplphysiol.00715.2016 (2017). Google Scholar

49. 

T. W. Secomb et al., “The mass transfer coefficient for oxygen transport from blood to tissue in cerebral cortex,” J. Cereb. Blood Flow Metab., 40 (8), 1634 –1646 https://doi.org/10.1177/0271678X19870068 (2020). Google Scholar

50. 

T. V. Esipova et al., “Oxyphor 2P: a high-performance probe for deep-tissue longitudinal oxygen imaging,” Cell Metab., 29 (3), 736 –744.e7 https://doi.org/10.1016/j.cmet.2018.12.022 1550-4131 (2019). Google Scholar

51. 

J. H. Kim and D. Ress, “Arterial impulse model for the BOLD response to brief neural activation,” Neuroimage, 124 (Pt A), 394 –408 https://doi.org/10.1016/j.neuroimage.2015.08.068 NEIMEF 1053-8119 (2016). Google Scholar

52. 

W. E. L. Brown and A. V. Hill, “The oxygen-dissociation curve of blood, and its thermodynamical basis,” Proc. R. Soc. Lond. B, 94 (661), 297 –334 https://doi.org/10.1098/rspb.1923.0006 PRLBA4 0080-4649 (1923). Google Scholar

53. 

G. R. DiResta, J. B. Lee and E. Arbit, “Measurement of brain tissue specific gravity using pycnometry,” J. Neurosci. Methods, 39 (3), 245 –251 https://doi.org/10.1016/0165-0270(91)90103-7 JNMEDT 0165-0270 (1991). Google Scholar

54. 

A. S. Popel, “Theory of oxygen transport to tissue,” Crit. Rev. Biomed. Eng., 17 (3), 257 –321 CRBEDR 0278-940X (1989). Google Scholar

55. 

I. G. Kassissia et al., “Tracer oxygen distribution is barrier-limited in the cerebral microcirculation,” Circ. Res., 77 (6), 1201 –1211 https://doi.org/10.1161/01.RES.77.6.1201 CIRUAL 0009-7330 (1995). Google Scholar

56. 

S. N. Jespersen and L. Ostergaard, “The roles of cerebral blood flow, capillary transit time heterogeneity, and oxygen tension in brain oxygenation and metabolism,” J. Cereb. Blood Flow Metab., 32 (2), 264 –277 https://doi.org/10.1038/jcbfm.2011.153 (2012). Google Scholar

57. 

A. Gjedde et al., “Cerebral metabolic response to low blood flow: possible role of cytochrome oxidase inhibition,” J. Cereb. Blood Flow Metab., 25 (9), 1183 –1196 https://doi.org/10.1038/sj.jcbfm.9600113 (2005). Google Scholar

58. 

M. S. Vafaee and A. Gjedde, “Model of blood-brain transfer of oxygen explains nonlinear flow-metabolism coupling during stimulation of visual cortex,” J. Cereb. Blood Flow Metab., 20 (4), 747 –754 https://doi.org/10.1097/00004647-200004000-00012 (2000). Google Scholar

59. 

T. Hayashi et al., “A theoretical model of oxygen delivery and metabolism for physiologic interpretation of quantitative cerebral blood flow and metabolic rate of oxygen,” J. Cereb. Blood Flow Metab., 23 (11), 1314 –1323 https://doi.org/10.1097/01.WCB.0000090506.76664.00 (2003). Google Scholar

60. 

H. Piilgaard and M. Lauritzen, “Persistent increase in oxygen consumption and impaired neurovascular coupling after spreading depression in rat neocortex,” J. Cereb. Blood Flow Metab., 29 (9), 1517 –1527 https://doi.org/10.1038/jcbfm.2009.73 (2009). Google Scholar

61. 

K. E. Schlageter et al., “Microvessel organization and structure in experimental brain tumors: microvessel populations with distinctive structural and functional properties,” Microvasc. Res., 58 (3), 312 –328 https://doi.org/10.1006/mvre.1999.2188 MIVRA6 0026-2862 (1999). Google Scholar

62. 

H. R. Weiss et al., “Quantitative regional determination of morphometric indices of the total and perfused capillary network in the rat brain,” Circ. Res., 51 (4), 494 –503 https://doi.org/10.1161/01.RES.51.4.494 CIRUAL 0009-7330 (1982). Google Scholar

63. 

J. H. Wilkinson, J. W. Hopewell and H. S. Reinhold, “A quantitative study of age-related changes in the vascular architecture of the rat cerebral cortex,” Neuropathol. Appl. Neurobiol., 7 (6), 451 –462 https://doi.org/10.1111/j.1365-2990.1981.tb00245.x NANEDL 1365-2990 (1981). Google Scholar

64. 

P. M. Gross et al., “Differences in function and structure of the capillary endothelium in gray matter, white matter and a circumventricular organ of rat brain,” Blood Vessels, 23 (6), 261 –270 https://doi.org/10.1159/000158652 BLVSAB 0303-6847 (1986). Google Scholar

65. 

H. Laursen and N. H. Diemer, “Capillary size and density in the cerebral cortex of rats with a porto-caval anastomosis,” Acta Neuropathol., 40 (2), 117 –122 https://doi.org/10.1007/BF00688699 ANPTAL 1432-0533 (1977). Google Scholar

66. 

A. K. Sinha et al., “Cerebral regional capillary perfusion and blood flow after carbon monoxide exposure,” J. Appl. Physiol., 71 (4), 1196 –1200 https://doi.org/10.1152/jappl.1991.71.4.1196 (1991). Google Scholar

67. 

D. K. Clark et al., “Oxygen diffusion, conductivity and solubility coefficients in the microarea of the brain,” Adv. Exp. Med. Biol., 94 697 –704 https://doi.org/10.1007/978-1-4684-8890-6_96 AEMBAP 0065-2598 (1977). Google Scholar

68. 

L. D. Homer, J. B. Shelton and T. J. Williams, “Diffusion of oxygen in slices of rat brain,” Am J. Physiol., 244 (1), R15 –R22 https://doi.org/10.1152/ajpregu.1983.244.1.R15 (1983). Google Scholar

69. 

R. A. Ganfield, P. Nair and W. J. Whalen, “Mass transfer, storage, and utilization of O2 in cat cerebral cortex,” Am. J. Physiol., 219 (3), 814 –821 https://doi.org/10.1152/ajplegacy.1970.219.3.814 AJPHAP 0002-9513 (1970). Google Scholar

70. 

G. Thews, “A method for determination of oxygen diffusion coefficients, oxygen conductivity and oxygen solubility coefficients in brain tissue,” Pflugers Arch. Gesamte Physiol. Menschen Tiere, 271 227 –244 https://doi.org/10.1007/BF00363006 (1960). Google Scholar

71. 

T. Temma et al., “PET O-15 cerebral blood flow and metabolism after acute stroke in spontaneously hypertensive rats,” Brain Res., 1212 18 –24 https://doi.org/10.1016/j.brainres.2008.03.033 BRREAP 0006-8993 (2008). Google Scholar

72. 

M. Kobayashi et al., “Cerebral oxygen metabolism of rats using injectable 15O-oxygen with a steady-state method,” J. Cereb. Blood Flow Metab., 32 (1), 33 –40 https://doi.org/10.1038/jcbfm.2011.125 (2012). Google Scholar

73. 

S. Mekid and D. Vaja, “Propagation of uncertainty: expressions of second and third order uncertainty with third and fourth moments,” Measurement, 41 (6), 600 –609 https://doi.org/10.1016/j.measurement.2007.07.004 0263-2241 (2008). Google Scholar

Biographies of the authors are not available.

CC BY: © The Authors. Published by SPIE under a Creative Commons Attribution 4.0 International License. Distribution or reproduction of this work in whole or in part requires full attribution of the original publication, including its DOI.
Sang Hoon Chong, Yihong Ong, Mirna El Khatib, Srinivasa Rao Allu, Ashwin B. Parthasarathy, Joel H. Greenberg, Arjun G. Yodh, and Sergei A. Vinogradov "Real-time tracking of brain oxygen gradients and blood flow during functional activation," Neurophotonics 9(4), 045006 (28 November 2022). https://doi.org/10.1117/1.NPh.9.4.045006
Received: 6 August 2022; Accepted: 1 November 2022; Published: 28 November 2022
Lens.org Logo
CITATIONS
Cited by 1 scholarly publication.
Advertisement
Advertisement
KEYWORDS
Oxygen

Brain

Picosecond phenomena

Phosphorescence

Blood circulation

Tissues

Laser speckle contrast imaging

RELATED CONTENT


Back to Top