A 10μm pixel pitch 1280×1024 Readout Integrated Circuit (ROIC) for MWIR applications is designed and fabricated using 0.18 μm CMOS process. It operates in snapshot mode supporting both Integrate-Then-Read (ITR) and IntegratedWhile-Read (IWR) configurations. The ROIC pixel has direct injection (DI) input stage and provides 2-bit programmable pixel gain. It has a minimum charge capacity of 0.7 Mé and a maximum full-well-capacity (FWC) of more than 6.3 Mé in ITR mode. 4, 8 and 16 analog video output modes are also supported with a maximum frame rate of 120 fps at 16-output mode. All digital timing and analog biasing are programmable through a serial interface. Integration time is programmable with 0.1 μs resolution by internal timing circuitry. It supports binning, windowing and antiblooming functions. The ROIC operates with 3.3 V and 1.8 V supplies and dissipates less than 175 mW in 4-output mode of operation at 30 fps. An Analog-Front-End (AFE) card is designed to operate the ROIC and convert analog video outputs into 14-bit digital value. Digitized video data is further processed by 1-point and 2-point Non-Uniformity Correction (NUC), histogram equalization and bad pixel replacement algorithms. The ROIC has been tested with a prototype FPA at 77K. Measurement results of ASEL128010 indicate that it is functional at all operating modes including windowing and binning. The input referred noise level of the ROIC is 877 é at 6.3 Mé FWC.
Microbolometer detectors have drawn attention due to their advantages such as small dimensions, light weight, low power consumption and no cooling requirement. In recent years, studies regarding the microbolometers have accelerated. Research on uncooled infrared microbolometer detectors was initiated at ASELSAN in 2014. As result of these activities, microbolometers with high TCR and low 1/f noise level have been achieved based on vanadium oxide active material. Pixel structures with high fill factor ratios are accomplished using double layer pixel architecture and high responsivity values were obtained by FPA optimizations. 640 x 480 format and 17 μm pixel pitch microbolometer FPAs along with VOx sensing layer were produced. These detectors have demonstrated state of the art NETD values (< 30 mK @ f/1) and with such properties that could be used in various applications which require high frame rates due to their low time constant values (< 12 ms). FPA fabrication has been performed on 8” CMOS ROIC wafers which are also designed by ASELSAN. 17 μm pixel pitch 640 x 480 format ROIC has been developed for resistive microbolometer detector arrays. ROIC wafers were fabricated using 0.18 μm CMOS process where 3.3 V analog and 1.8 V digital supplies are used. The ROIC has 4 analog video outputs and 2 analog reference outputs. It can be operated at 1, 2 or 4 output modes depending on the frame rate requirement. In 2-output mode of operation power consumption of the ROIC is less than 150 mW. In this paper, the details of the microbolometer detectors including the ROIC design, vacuum packaging and detector performances are presented.
ASELSAN A.S., the largest defense company in Turkey, develops high performance electro-optical systems for land, air and naval applications. Research activities on developing Mercury Cadmium Telluride (MCT) detectors are on-going for MW and LW infrared bands. In this paper, recent results on Cadmium Zinc Telluride substrate growth, long wavelength (LW) Mercury Cadmium Telluride (MCT) detector fabrication and readout integrated circuit design are summarized. LW MCT focal plane arrays with a format of 320×256/30 μm are fabricated. Noise Equivalent Temperature Difference (NETD) of these focal plane arrays (FPA) are 45.7 mK and 59.9 mK (f/1.5, 77K) while the operabilites are 98.14% and 99.28%, respectively.
A 15 μm pixel pitch 640×512 Readout Circuit (ROIC) for MWIR applications is designed and fabricated using 0.18 um CMOS process. The ROIC is implemented using Direct Injection (DI) input stage with programmable pixel gain where maximum full-well-capacity (FWC) is more than 13Mé. All analog current and voltage bias values can be programmed through a digital interface. Additionally, integration time can be programmed with 0.1 µsec resolution by internal timing circuitry. ROIC has 1, 2 and 4 output modes with a frame rate of 120fps at 4 output mode. The design supports IntegrateThen-Read (ITR) and Integrate-While-Read (IWR) modes in snapshot operation. Photodetector reverse bias voltage is controlled by adjusting the bias of the common-gate input stage at the input of DI pixel. An on-chip low-dropout voltage regulator is used to generate the detector common voltage. With 2x2 binning feature, the ROIC can also be used for 30 µm pixel pitch 320x256 photodetector arrays. An Analog-Front-End (AFE) card has been designed to operate the ROIC and to convert analog video output to a 14-bit digital value. This digital video data is handled by external video processor card which supports 1-point and 2-point Non-Uniformity Correction (NUC), histogram equalization, bad pixel replacement and filtering. The ROIC has been extensively tested with a prototype FPA at 77°K. According to these test results, functionality of all modes have been verified and a noise level of 700é is achieved at 4.5Mé FWC.
This paper reports a 640x512 SWIR ROIC with 15um pixel pitch that is designed and fabricated using 0.18um CMOS process. Main challenge of SWIR ROIC design is related to input circuit due to pixel area and noise limitations. In this design, CTIA with single stage amplifier is utilized as input stage. The pixel design has three pixel gain options; High Gain (HG), Medium Gain (MG), and Low Gain (LG) with corresponding Full-Well-Capacities of 18.7ké, 190ké and 1.56Mé, respectively. According to extracted simulation results, 5.9é noise is achieved at HG mode and 200é is achieved at LG mode of operation. The ROIC can be programmed through an SPI interface. It supports 1, 2 and 4 output modes which enables the user to configure the detector to work at 30, 60 and 120fps frame rates. In the 4 output mode, the total power consumption of the ROIC is less than 120mW. The ROIC is powered from a 3.3V analog supply and allows for an output swing range in excess of 2V. Anti-blooming feature is added to prevent any unwanted blooming effect during readout.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.